Controllers

Astero-lite +

Astero-lite + is the basic model of RO controller series; it is just a simple controller with display for TDS. There is a mimic of reverse osmosis system with LED for ease of understanding. The RO controller can be well installed on the skid.

RO-Lite

Download

  • Complete RO Logic Preprogrammed.

  • Ideally Suited for Small Sized RO's

  • Auto / Manual Option

  • Automatically Flushes the Membrane During Starting and Stopping

  • Process Flow Diagram with Bright LED for Ease of Understanding

  • Mimic Diagram with 11 LED’s for I/O indications

  • Facility to Bypass LPS/Floaty/Both in Auto mode

  • Preprogrammed Settings Eliminates the Need of Skilled Operator

  • Separate Power and Control Terminals

  • Pressfit Connector for Input Terminals for Ease of Wiring

  • Large Terminals for Rugged Wiring

  • Inbuilt TDS Indicator

Astero Mini

Astero Mini controller combines the typical operation modes of various reverse osmosis systems, adopts high-performance microprocessor chip and takes multiple reliability measures, the technology is mature and operation reliable; the control panel displays the operation status of the system by visual flow chart with LED indication lamp embedded. RO controller operates in a five-in-four-out way.

Astero™ Mini

Download

  • Complete RO Operating Logic in built

  • Suitable for RO Plant of Any Capacity

  • 2 Line Alphanumeric Display With Keypad For Programming

  • Mimic Diagram With 8 Led Annunciator

  • 5 Key Buttons To Make Operating Easy

  • Automatically Flushes The Membrane During Starting And Stopping And After Set Time Period

  • Auto / Manual Mode

  • In Built Flow Rate Indicator With Totaliser

  • In Built Conductivity Indicator

  • In Built Operation Hour Counter

  • Equipped To Suit Auto-Multiport Valve In Pre-Treatment

  • Easy Wiring Through Rear Terminal

Accessories as Required

•  Conductivity Sensor

•  Flow Sensor of required size

•  Low Level Switch

•  Floaties(2)

•  Low Pressure Switch

•  High Pressure Switch

RO Matic NG

The reverse osmosis controller can give an idea about plant health by measuring conductivity, flow of product and feed water, pressure or pH/ORP and gives signal to pump and valves as per logic. An integral process mimic diagram with LED indicators along with a four line alphanumeric display ensures easy understanding of the plant status. This controller can be easily integrated with panels of any capacity system and prove to be a cost effective solution over conventional PLCs.

RO-Matic NG

Download

  • Complete RO Operating Logic In Built

  • Automatically Flushes The Membrane During Starting And Stopping

  • Heavy Duty Extruded Aluminum Box With ABS Front Plate

  • Rear Terminal Strip For Ease Of Wiring

  • 4 Line Alphanumeric Display With Keypad For Programming

  • Mimic Diagram With 8 LED Annunciator

  • In Built Conductivity Indicator

  • In Built Flow Indicator

  • In Built pH/ ORP/ Temperature/ Pressure Indicator

  • RS 485 Output For Remote Data Transfer

  • SMS Alerts With Remote Monitoring/Data Logging (Optional)

Accessories as Required

•  Conductivity Sensor

•  Flow Sensor of required size

•  Floaty

•  Low Pressure Switch

•  High Pressure Switch

•  pH Transmitter

•  ORP Transmitter

•  Pressure Transmitter

UF-Matic

Universal logic controller to suit all makes of membrane and all types of operating logics. It can be used to control not only feed and backwash pump but also 10 other outputs such as dosing pump and solenoid/motorized valve. Up to 30 user programmable steps (option of preprogrammed UF-Matic for specific membrane also available) with field settable timings. Facility to have CEB/CIP at desired interval also available.

UF-Matic

Download

  • Heavy Duty Extruded Aluminum Box With ABS Front Plate

  • Rear Terminal Strip For Ease Of Wiring

  • Universal Suitable For Any Logic & For All Type Of Membranes

  • User Settable : Up To 10 Valves & 2 Pumps Programmable At Site

  • All Timings Are Settable At Site

  • Can Program Up To 30 Steps

  • User Settable Frequency For CEB & Backwash Cycles

  • Settable Pump ON & Pump OFF Delay Avoids Water Hammering

  • One Flow Input (With Inbuilt Totalizer )

  • Separate LED For Every Input & Output

  • Can Be Used Even For MB Automation

  • • Backwash/Regeneration Cycle Can Be Initiated Based On Pump Time/Volume/Pulse Input

*Optionally available with remote monitoring system

STP/ETP-Matic NG

It's unique microprocessor based controller ideally suitable for most waste water treatment plant with facility to control feed pump, blower, sludge pump and transfer pump. Each drive can be automatically switched over to its standby drive after a set time interval. An integral process mimic diagram with LED indicators along with a four line alphanumeric display ensures easy understanding of the status of operation of the plant. This controller can be easily integrated with panels of any capacity system and prove to be a cost effective solution over conventional PLCs.
Built in RS-485 output helps in logging the data electronically, which can be reproduced for the inspection or audit purpose by government body.

STP-Matic

Download

  • Heavy Duty Extruded Aluminum Enclosure With ABS Front Plate

  • 20 X 4 Alphanumeric Display & Mimic Diagram With 8 LED's

  • Complete ETP/STP Logic Pre-programmed

  • Drains The Sludge Periodically

  • Automatically Switches Over To Stand-By Motor Or Blower After A Preset Time

  • All Settings Are Password Protected (Can Be Done Through 3 Front Keys)

  • Inbuilt Operation Hour Meter

  • RS485 O/P For Data Logging (Local Or Remote)

  • One Flow Sensor Input With Totalizer

  • 4 Analog Inputs (Can Be Configured As Blower/PH/DO/Flow)

  • Blower Can Be Interlocked With DO Level To Reduce Power Consumption

  • Inbuilt Pump ON Delay To Avoid Initial Dip In Voltage

INSTRU-Matic

7 channel data indicator cum controller for measurement and control of various parameters like conductivity, TDS, pH, ORP, Flow, Temperature, DO, Fluroxene, Level, Pressure, Intensity current etc.
Each Instrument comes with RS485 communication port which can be used for BMS/SCADA/Remote Monitoring.

INSTRU-Matic

Download

  • Complete Data Indication Of Plant

  • 4 Line Alphanumeric Display With Keypad For Programming & Setting

  • Bright LED Annunciator For Fault Indication

  • Inbuilt Conductivity/TDS Indicator

  • Inbuilt Dual Channel Flow Rate Indicator (With Totaliser For Channel 1)

  • 7 Analog Input

  • 8 Potential Free Output- Any Output Can Be Configured To Any Channel With Switching At High Or Low Set Point

  • RS 485 Output

Accessories as Required

•  2  Flow Sensors

•  pH, ORP, Pressure, Temperature transmitter

Like what you see here? We believe that we can offer great services to you to create a unique online experience.

Let's work together
EmbarkTeamControllers Models